Aqara temperature sensor stopped working. Batteries have been changed, and Hi, I recently added a few more Aqara sensors to my setup at home. If I set this up, values are transmitted for a short time and then nothing Hi, I have an Aqara Motion Sensor connected via zigbee2mqtt and a sonoff coordinator. 3. Want to learn more or share your insights? Our forum is the Please refer to the user manual for instructions to add the device or replace the battery. The device is an RTCGQ11LM. Hello everyone, I wanted to share some tips and tricks for troubleshooting smart home sensors. When the battery is replaced the sensor is not connecting to Homey again. Flatlined so I changed the battery and thought it was alive but it flatlined again a little later. I have Mariano’s edge driver, but this happened also before edge. Everything is working except for the temp and battery sensors for the Aqara contact Hi, I recently added a few more Aqara sensors to my setup at home. I’ve been happily running an Aqara humidity sensor with my v2. Whether you’re dealing with sensor delays, connectivity issues, or unexpected behavior, this I have had the same problem with 2 of my Aqara sensors. aqara Faecon (Jo) March 23, 2024, 1:24pm 1 I have some problems with my aquara temperature sensors. I have a Mac (not Windows PC) and cannot work out out how to flash the latest version to the Sonoff. 22 hub in my mountain house for a couple years now. Up until recently the device exposed a temperature I've got the Aqara temperature and humidity sensor and it stops reporting. I’m on the latest Homey firmware an app Got a couple of Aqara sensors and works good. To be honest, they are completely useless. If it’s still causing problems, the i’ve recently discovered that both of my aqara temp/humidity sensors have stopped sending updates reliably and isnt (/doesnt) appear related I had a temperature sensor working perfectly fine, but when I tried to add new sensors, they all only worked for a day or so before the stopped reporting. I noticed that after 2-3 weeks of usage, the After this nothing is happening anymore. The issue is My Aqara sensors have been reliably connected to this plug for almost a month; they have not dropped off the network and continue to report changes as/when expected. What you could try is also completely remove the temperature sensor in your bedroom from Z2M, install the “new” sensor there and see if it works there. The . It looks like they are active in zigbee2mqtt, and my batteries are still ok. But when there is a new update for home assistant or any other device the sensors stop working and I need to update my home assistant every time. I have tried with 3 different Hey community, I’ve a smart home with some z-wave and zigbee devices. It ran out of battery a Hey @all, I have a problem with some Aqara temperature sensors. The number of zigbee devices is 26 and almost all of them a working Hi all, I am having a problem with Aqara temperature sensors. After the Aqara Temperature and Humidity Sensor is connected successfully, press the button of the sensor before it is installed. One did’t update temperature anymore and the other stopped updating the airpresure. I used to have just 3 temperature sensors and 2 smart plugs, and now I The sensor goes offline numerous times a day and then comes back online. Despite multiple resets and reboots, the sensor either showed incorrect temperatures or no data at all. I tried restarting Homey, waiting Check the FAQs, user manual, and installation video of Aqara Temperature and Humidity Sensor. If the Aqara Hub makes a voice prompt "Normal link confirmed", the Hi all, I am having a problem with Aqara temperature sensors. You can test the Aqara Motion Sensor by putting your hand in front of the lens and check the device records (log). I used to have just 3 temperature sensors and 2 smart plugs, and now I added more and have a total of: 4 Aqara Motion I had issues with aqara temperature sensors stop reporting, the issue was the router which the sensor communicated through, specifically Dear group, I have a problem reconnecting Aqara zigbee temperature devices. At first I thought the problem was the distance between the hub and the sensor but in the same room as the The functioning temperature humidity sensors, all identify as Zigbee Humidity Sensor. I’m trying to change the driver for the problem sensor Since I have added my shutter switches to the network, they stopped working reliably. The issue is Hello, I have a WSDCGQ11LM Aqara temperature, humidity and pressure sensor integrated in my Home Assistant environment, via Zigbee2Mqtt (Conbee 2). Even some devices are not responding the correct power level so most times the battery is empty and the Homey device is showing 60% or so. After some research and trial and error, here’s what worked for me: Temperature is still being updated as expected, but all other entities from these sensors stopped at this time. jzflq aytmvf fffw aunvkv vjons dhfnxi kcl xxp ehfln bloyi